Mechanical Characteristics of Individualized Biodegradable Augmentation Scaffold-In Vitro Pilot Study.

The alveolar ridge reconstruction of vertical and combined bone defects is a non-predictable procedure with varying percentages of success. The greatest challenge for vertical and combined bone augmentation is to maintain mechanical stability of the bone graft; therefore, it is mandatory to provide and preserve space for bone regeneration. The development of biomaterials and 3D printing has enabled the use of polymer scaffolds in the reconstruction of alveolar ridge defects. The aim of this pilot study was to evaluate the mechanical characteristics of an innovative individualized biodegradable polylactic acid (PLA) scaffold, under dynamic conditions, simulating biodegradation and the influence of masticatory forces. After the design and 3D printing of PLA scaffolds, two groups of 27 scaffolds were formed according to the compression testing procedure. The compression tests were performed in occlusal and lateral directions. In each of the two groups, nine subgroups of three scaffolds were formed for different testing periods during in vitro degradation with a total period of 16 weeks. Results showed that biodegradation and load application had no significant influence on mechanical characteristics of tested scaffolds. It can be concluded that simulated masticatory forces and biodegradation do not significantly influence the mechanical characteristics of an individualized biodegradable augmentation scaffold.

The Shear Bond Strength between Milled Denture Base Materials and Artificial Teeth: A Systematic Review.

The data about bond strength between digitally produced denture base resins and artificial teeth are scarce. Several studies investigated shear bond strength values of milled denture base resins and different types of artificial teeth. The purpose of the present study was to compare and evaluate the available evidence through a systematic review. A bibliographic search was conducted in PubMed, Scopus, and Web of Science to assess adequate studies published up to 1 June 2022. This review followed the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) guidelines. The appropriate studies that determined the shear bond strength values between milled denture base resins and artificial teeth were selected. The initial search identified 103 studies, which were included in the PRISMA 2020 flow diagram for new systematic reviews. Three studies met the inclusion criteria, and all of them present a moderate risk of bias (score 6). Two studies found no statistical differences between heat-polymerized and CAD/CAM (milled) denture base materials when attached with different types of artificial teeth, while one study showed higher values of CAD/CAM (milled) denture base materials. Bonding agents ensure bonding strength at least similar to the conventional methods. In order to improve the quality of future studies, it would be advantageous to use a larger number of specimens with standardized dimensions and a blinded testing machine operator to decrease the risk of bias.

THE EFFECT OF LOCAL AND SYSTEMIC FACTORS ON DENTAL IMPLANT FAILURE - ANALYSIS OF 670 PATIENTS WITH 1260 IMPLANTS.

The etiopathogenesis of dental implant failure is multifactorial and may include numerous local and systemic factors, however, studies including both local and systemic factors are still lacking. Therefore, the aim of this study was to evaluate whether periodontal disease, oral hygiene index, i.e. bleeding on probing (BOP), full mouth plaque index (FMPI), smoking, systemic diseases, as well as implant characteristics (length and diameter) affect failure of implant-prosthodontic therapy. Data on 670 patients were retrieved in whom 1260 dental implants had been placed and followed-up for at least five to ten years. Categorical data were analyzed by the χ2-test, whereas Mann-Whitney test was used for continuous variables (age, BOP and FMPI). The values of p<0.05 were considered significant. The effect of local and systemic factors on the success of implant-prosthodontic therapy was assessed by multiple logistic regression analysis. Forty-five (6.7%) patients had systemic diseases, of which diabetes mellitus was most common, followed by atherosclerosis, diabetes and atherosclerosis, diabetes mellitus type 1, lymphoma, and hepatitis C. One-third (33.4%) of the patients were smokers. Periodontal disease was present in 170 patients, while 500 patients were without periodontal disease. Nine implants were lost during the period of five years. There were no differences regarding the type of implant or type of connection to the prosthetic suprastructure. However, most of these patients had a periodontal disease. There were no significant differences in dental implant failure rates between smokers and non-smokers or between patients with and without systemic diseases. Furthermore, the results of this study showed that implant type (straight vs. tapered) and type of connection with prosthodontic appliance (cemented or screw retained) did not affect BOP and FMPI. In smokers, significant improvement of BOP and FMPI was noticed. Initially, smokers had a significantly worse BOP (0.0037) when compared to non-smokers; however, there were no differences regarding FMPI (p=0.4218) between the two groups. In patients with periodontal disease, improvement of BOP and FMPI was seen at 5-year follow-up and no significant differences were found when compared to patients without periodontal disease. There were no significant differences in BOP and FMPI between patients with and without diabetes at 5-year follow-up. Atherosclerosis had a significant negative effect on BOP, but not on FMPI at 5-year follow-up. It is concluded that periodontal disease had a significant impact on the implant-prosthodontic therapy.

Sealing Efficacy of the Original and Third-Party Custom-Made Abutments-Microbiological In Vitro Pilot Study.

Implant-abutment connection (IAC) is a key factor for the long-term success and stability of implant-supported prosthodontic restoration and its surrounding tissues. Misfit between prosthodontic abutment and implant at the IAC leads to technical and biological complications. Two kinds of prosthodontic abutments are currently available on the market: original and third-party abutments. The aim of this pilot study was to test and compare the internal fit (gap) at the implant-abutment interface depending on the abutment fabrication method based on microbial leakage in static conditions and the need for the use of gap sealing material. Two groups of 40 implants were formed on the basis of the type of abutment. In each of the groups of two implant systems, two subgroups of 10 implants were formed. The tested subgroups consisted of 10 implants with sealing material and a negative control subgroups consisting of 10 implants without any sealing material. The test material, GapSeal (Hager and Werken, Duisburg, Germany) was applied in the test subgroups. The implant-abutment assemblies were contaminated with a solution containing Staphylococcus aureus and Candida albicans for 14 days under aerobic conditions. Results showed that there was no statistically significant difference regarding the microbial leakage between the original and third-party custom-made abutments, regardless of the use of sealing material. It can be concluded that the abutment fabrication method has no significant influence on sealing efficacy regarding the bacterial and fungal leakage in static conditions.

Additively Manufactured Commercial Co-Cr Dental Alloys: Comparison of Microstructure and Mechanical Properties.

Laser-powder bed fusion (LPBF) is one of the preferred techniques for producing Co-Cr metal structures for dental prosthodontic appliances. However, there is generally insufficient information about material properties related to the production process and parameters. This study was conducted on samples produced from three different commercially available Co-Cr dental alloys produced on three different LPBF machines. Identically prepared samples were used for tensile, three-point bending, and toughness tests. Light microscopy (LM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD) analyses of microstructure were performed after testing. Differences were observed in microstructures, which reflected statistically significant differences in mechanical properties (one-way analysis of variance (ANOVA) and Scheffé post hoc test (α = 0.05)). The material produced on the 3D Systems DMP Dental 100 had 24 times greater elongation ε than the material produced on the Sysma MySint 100 device and the EOS M100 machine. On the other hand, the material produced on the EOS M100 had significantly higher hardness (HV0.2) than the other two produced materials. However, the microstructure of the Sysma specimens with its morphology deviates considerably from the studied group. LPBF-prepared Co-Cr dental alloys demonstrated significant differences in their microstructures and, consequently, mechanical properties.

Comparison of Mechanical Properties of 3D-Printed, CAD/CAM, and Conventional Denture Base Materials.

PURPOSE: To evaluate and compare the mechanical properties (flexural strength and surface hardness) of different materials and technologies for denture base fabrication. The study emphasized the digital technologies of computer-aided design/computer-aided manufacturing (CAD/CAM) and three-dimensional (3D) printing. MATERIALS AND METHODS: A total of 160 rectangular specimens were fabricated from three conventional heat-polymerized (ProBase Hot, Paladon 65, and Interacryl Hot), three CAD/CAM produced (IvoBase CAD, Interdent CC disc PMMA, and Polident CAD/CAM disc), one 3D-printed (NextDent Base), and one polyamide material (Vertex ThermoSens) for denture base fabrication. The flexural strength test was the three-point flexure test, while hardness testing was conducted using the Brinell method. The data were analyzed using descriptive and analytical statistics (α = 0.05). RESULTS: During flexural testing, the IvoBase CAD and Vertex ThermoSens specimens did not fracture during loading. The flexural strength values of the other groups ranged from 71.7 ± 7.4 MPa to 111.9 ± 4.3 MPa. The surface hardness values ranged from 67.13 ± 10.64 MPa to 145.66 ± 2.22 MPa. There were significant differences between the tested materials for both flexural strength and surface hardness. There were also differences between some materials with the same polymerization type. CAD/CAM and polyamide materials had the highest flexural strength values. Two groups of CAD/CAM materials had the highest surface hardness values, while a third, along with the polyamide material, had the lowest. The 3D-printed materials had the lowest flexural strength values. CONCLUSIONS: Generally, CAD/CAM materials show better mechanical properties than heat-polymerized and 3D-printed acrylics do. Nevertheless, a material's polymerization type is no guarantee of its optimal mechanical properties.

Comparison of shear bond strengths of different types of denture teeth to different denture base resins.

PURPOSE: To determine the shear bond strengths of different denture base resins to different types of prefabricated teeth (acrylic, nanohybrid composite, and cross-linked) and denture teeth produced by computer-aided design/computer-aided manufacturing (CAD/CAM) technology. MATERIALS AND METHODS: Prefabricated teeth and CAD/CAM (milled) denture teeth were divided into 10 groups and bonded to different denture base materials. Groups 1-3 comprised of different types of prefabricated teeth and cold-polymerized denture base resin; groups 4-6 comprised of different types of prefabricated teeth and heat-polymerized denture base resin; groups 7-9 comprised of different types of prefabricated teeth and CAD/CAM (milled) denture base resin; and group 10 comprised of milled denture teeth produced by CAD/CAM technology and CAD/CAM (milled) denture base resin. A universal testing machine was used to evaluate the shear bond strength for all specimens. One-way ANOVA and Tukey post-hoc test were used for analyzing the data (α=.05). RESULTS: The shear bond strengths of different groups ranged from 3.37 ± 2.14 MPa to 18.10 ± 2.68 MPa. Statistical analysis showed significant differences among the tested groups (P<.0001). Among different polymerization methods, the lowest values were determined in cold-polymerized resin.There was no significant difference between the shear bond strength values of heat-polymerized and CAD/CAM (milled) denture base resins. CONCLUSION: Different combinations of materials for removable denture base and denture teeth can affect their bond strength. Cold-polymerized resin should be avoided for attaching prefabricated teeth to a denture base. CAD/CAM (milled) and heat-polymerized denture base resins bonded to different types of prefabricated teeth show similar shear bond strength values.

A study of the flexural strength and surface hardness of different materials and technologies for occlusal device fabrication.

STATEMENT OF PROBLEM: With the emergence of digital technologies, new materials have become available for occlusal devices. However, data are scarce about these different materials and technologies and their mechanical properties. PURPOSE: The purpose of this in vitro study was to investigate the flexural strength and surface hardness of different materials using different technologies for occlusal device fabrication, with an emphasis on the digital technologies of computer-aided design and computer-aided manufacturing (CAD-CAM) and 3D printing. MATERIAL AND METHODS: A total of 140 rectangular specimens were fabricated from two 3D-printed (VarseoWax Splint and Ortho Rigid), 2 CAD-CAM-produced (Ceramill Splintec and CopraDur), and 3 conventional autopolymerizing occlusal device materials (ProBase Cold, Resilit S, and Orthocryl) according to ISO 20795-1:2013. Flexural strength and surface hardness were determined for 10 specimens of each tested material using the 3-point bend test and the Brinell method. The data were analyzed using descriptive statistics and 1-way ANOVA with Bonferroni corrections (α=.05). RESULTS: Surface hardness values ranged from 28.5 ±2.5 MPa to 116.2 ±1.6 MPa. During flexural testing, neither the CopraDur nor the VarseoWax Splint specimens fractured during loading within the end limits of the penetrant's possible movement. Flexural strength values for other groups ranged from 75.0 ±12.0 MPa to 104.9 ±6.2 MPa. Statistical analysis determined significant differences among the tested materials for flexural strength and surface hardness. CONCLUSIONS: Mechanical properties among different occlusal device materials were significantly different. Acrylic resins were less flexible than polyamide and nonacrylic occlusal device materials for 3D printing but had higher and more consistent values of surface hardness. Clinicians should consider the different mechanical properties of the available materials when choosing occlusal device materials.

Bioactive Ti + Mg composites fabricated by powder metallurgy: The relation between the microstructure and mechanical properties.

Metallic implant materials are biomaterials that have experienced major development over the last fifty years, yet some demands posed to them have not been addressed. For the osseointegration process and the outcome of endosseous implantation, it is crucial to reduce the stress shielding effect and achieve sufficient biocompatibility. Powder metallurgy (PM) was utilized in this study to fabricate a new type of titanium (Ti) + magnesium (Mg) bioactive composite to enable stress-shielding reduction and obtain better biocompatibility compared with that of the traditional Ti and Ti alloys used for dental implants. Such composites are produced by well-known cost-effective and widely used PM methods, which eliminate the need for complex and costly Ti casting used in traditional implant production. The relation between the microstructure and mechanical properties of as-extruded Ti + (0-24) vol% Mg composites was investigated with respect to the Mg content. The microstructure of the composites consisted of a biodegradable Mg component in the form of filaments, elongated along the direction of extrusion, which were embedded within a permanent, bioinert Ti matrix. As the Mg content was increased, the discrete filaments became interconnected with each other and formed a continuous Mg network. Young's modulus (E) of the composites was reduced to 81 GPa, while other tensile mechanical properties were maintained at the values required for a dental implant material. The corrosion behavior of the Ti + Mg composites was studied during immersion in a Hank's balanced salt solution (HBSS) for up to 21 days. The elution of Mg pores formed at former Mg sites led to a further decrease of E to 74 GPa. The studied compositions showed that a new Ti + Mg metallic composite should be promising for load-bearing applications in endosseous dental implants in the future.

Reproducibility of the Obtained Centric Relation Records in Patients with Disc Displacement with Reduction.

OBJECTIVE: The aim of this study was to investigate reproducibility of the position of centric relation in patients with disc displacement with reduction. MATERIALS AND METHODS: The test group included 30 subjects, diagnosed with disc displacement with reduction in right, left or both joints. The control group included 12 individuals with no signs and symptoms of temporomandibular disorders. Using chin point guidance with a jig, centric relation record was made three times by every participant, in a single session. Left and right condylar position for each centric relation record was determined and recorded using the electronic ultrasonic measuring device. The data were transferred to the computer, processed and analyzed. Condylar distances between centric relation records were measured (anteroposterior, vertical, transversal and linear values), and the data were statistically analyzed using the t and the F tests. RESULTS: No statically significant difference was found between the test and the control groups. Two thirds of study participants demonstrated condylar position of the repeated centric relation recording within the area of 0.3 mm in diameter. For more than 90% of participants that area was within 0.4 mm. CONCLUSIONS: There is no difference in reproducibility of the centric relation between patients with disc displacement with reduction and healthy temporomandibular joint individuals (p>0.05). When doing centric relation record on a patient with disc displacement with reduction there is no need for previous splint therapy and standard precautions are acceptable. The obtained results must be interpreted within the experimental group, and not projected on the other groups of temporomandibular disorders.

Titanium Ions Release from an Innovative Titanium-Magnesium Composite: an in Vitro Study.

BACKGROUND: The innovative titanium-magnesium composite (Ti-Mg) was produced by powder metallurgy (P/M) method and is characterized in terms of corrosion behavior. MATERIAL AND METHODS: Two groups of experimental material, 1 mass% (Ti-1Mg) and 2 mass% (Ti-2Mg) of magnesium in titanium matrix, were tested and compared to commercially pure titanium (CP Ti). Immersion test and chemical analysis of four solutions: artificial saliva; artificial saliva pH 4; artificial saliva with fluoride and Hank balanced salt solution were performed after 42 days of immersion, using inductively coupled plasma mass spectrometry (ICP-MS) to detect the amount of released titanium ions (Ti). SEM and EDS analysis were used for surface characterization. RESULTS: The difference between the results from different test solutions was assessed by ANOVA and Newman-Keuls test at p<0.05. The influence of predictor variables was found by multiple regression analysis. The results of the present study revealed a low corrosion rate of titanium from the experimental Ti-Mg group. Up to 46 and 23 times lower dissolution of Ti from Ti-1Mg and Ti-2Mg, respectively was observed compared to the control group. Among the tested solutions, artificial saliva with fluorides exhibited the highest corrosion effect on all specimens tested. SEM micrographs showed preserved dual phase surface structure and EDS analysis suggested a favorable surface bioactivity. CONCLUSION: In conclusion, Ti-Mg produced by P/M as a material with better corrosion properties when compared to CP Ti is suggested.

The relationship between Angle type of occlusion and recorded Bennett angle values.

STATEMENT OF PROBLEM: The Bennett angle can be an important parameter to accurately record and program into an articulator during restorative procedures. Few data exist regarding the impact and association of a patient's occlusion types on their recorded Bennett angle values. PURPOSE: The purpose of this in vivo study was to investigate the effect of occlusion type on recorded Bennett angle values. MATERIAL AND METHODS: This study included 98 participants (26.0 ±5.2 years) divided into 4 study groups: Angle class I; Angle class II, division 1; Angle class II, division 2; Angle class III. All recordings were obtained using an ultrasound mandibular recording device with 6 degrees of freedom and a clutch was attached to the mandible. On each participant, 3 protrusive, 3 left laterotrusive, and 3 right laterotrusive movements were recorded. The recording device's software automatically calculated Bennett angle for each participant's left and right mandibular fossae and the data were statistically analyzed. RESULTS: One-way ANOVA did not show significant differences among different Angle classes of occlusion for the Bennett angle values. The average Bennett angle value for all participants was 7.7 degrees. CONCLUSIONS: The results of this study suggest that different Angle occlusion classifications do not appear to have an impact on recorded Bennett angle values. The average Bennett angle value in this study was found to be approximately 8 degrees. This information should be considered when programming average values into an articulator with respect to desired negative error (shorter cusp) during restoration fabrication.

Centric slide in different Angle's classes of occlusion.

The purpose of this study was to test the possible differences in centric slide values between different Angle's classes of occlusion. The study included 98 participants divided into four groups: Angle's class I, Angle's class II, subdivision 1, Angle's class II, subdivision 2 and Angle's class III. All recordings were obtained using an ultrasound jaw tracking device with six degrees of freedom. The distance between the maximum intercuspation (reference position) and the centric occlusion was recorded at the condylar level. Anteroposterior, superoinferior and transversal distance of the centric slide were calculated for each participant, and the data were statistically analyzed (analysis of variance and Newman-Keuls post hoc test). No statistically significant difference was found in the anteroposterior and transversal distance of the centric slide between tested groups, while Angle's class II, subdivision 2 showed smaller vertical amount of the centric slide compared to Angle's class I and class II, subdivision 1. None of the 98 participants showed coincidence of centric occlusion and maximum intercuspation. Our results suggest that coincidence of the maximum intercuspation with the centric occlusion should not be expected. Smaller extent of the vertical distance of the centric slide could be morphological and a functional expression characteristic of the Angle's class II, subdivision 2.

Movements of temporomandibular condyles during swallowing.

There have been studies that investigated mandibular movements and positioning during swallowing, but the results were inconsistent, and still the exact position of the condyles during swallowing is unknown. The purpose of this investigation was to study the kinematics of the mandible and the condyles, and to determine the actual movement paths and position of mandible and condyles during the process of swallowing. The study was performed on a sample of 44 dental students. Measurements were done with an electronic axiograph. After non-occlusing attachment was fixed in the mouth, every subject swallowed for five times from the rest position. The final swallowing position of the left and the right condyles was measured in the sagittal plane. The final swallowing position of the sagittal incisal point was measured in sagittal, frontal and horizontal plane, and data was statistically analyzed. The condyles showed average movement toward posterior (left 0.17 mm, SD 0.28, right 0.16 mm, SD 0.25) and superior (left 0.14 mm, SD 0.20, right 0.14 mm, SD 0.23). Anterior and/or inferior position had 20% of participants. The average sagittal incisal point movement during swallowing was toward anterior (0.30 mm, SD 0.53) and superior (0.81 mm, SD 0.84). The mean mandibular lateral movement was 0.1 mm (SD 0.1). The results of the study suggest that retrusion during swallowing is not the rule, although on average there is a slight tendency of condylar movement toward posterior. Swallowing can be used as auxiliary method for determining vertical dimension of occlusion.

ARTICULATOR-RELATED REGISTRATION AND ANALYSIS OF SAGITTAL CONDYLAR INCLINATION.

The purpose of this investigation was to study sagittal condylar inclination values within a uniform sample (Angle class I occlusion) using 'articulator-related registration' and Camper's plane as a reference plane. The study was performed on a sample of 58 Angle class I subjects (mean age 25.1, SD 3.1). Measurements were performed with an ultrasonic jaw tracking device with six degrees of freedom. After a paraocclusal tray was fixed in the mouth, each subject had to make three protrusive movements and three right and left laterotrusive movements. From protrusive movements the software of the device automatically calculated the left and the right sagittal condylar inclination values used for setting of the articulator. The mean sagittal condylar inclinationvalue was 41.0° (SD 10.5) for the right joint and 40.7° (SD 9.8) for the left joint. The maximum value was 65.0° for the right and 68.6° for the left joint, and the minimum value was 13.7° for the right and 21.7° for the left joint. The results of this study suggested the average articulator setting for sagittal condylar inclination for fully dentate adult subjects to be 40° in relation to Camper's plane. This is especially important for the articulators that are set up in relation to Camper's plane.

Measurements of the sagittal condylar inclination: intraindividual variations.

AIMS: Sagittal condylar inclination is an important parameter during fabrication of prosthetic restorations. Existing data about intraindividual variations of sagittal condylar inclination are scarce. The purpose of this study was to investigate intra- and interindividual variations of the sagittal condylar inclination, depending on the position of the condyle in the temporomandibular joint. METHODOLOGY: The study included 51 subjects with Angle's Class I occlusion (21-32 years of age, mean 25.1). Measurements were done using an electronic axiograph. After a paraocclusal tray was fixed in the mouth, every subject had to make three protrusive movements, from which the device's software calculated the mean left and mean right sagittal condylar path. The mean left and right condylar path of each subject was divided into three equal sequences, based on whole condylar path length. Condylar inclination values for the first, second and third movement sequences were calculated. RESULTS: Results showed significant differences between movement sequences (P < 0.05). For the left joint, condylar inclination values in the first condylar movement sequence demonstrated, on the average, 14.4% higher values compared to the second movement sequence, and 39.2% higher values than in the third movement sequence. For the right joint, the first condylar movement sequence demonstrated, on the average, 15.8% higher values compared to the second movement sequence, and 41.5% higher values than the third movement sequence. CONCLUSIONS: Results suggest that condylar movement in the sagittal direction is not uniform. Mean left and mean right condylar inclination values do not necessarily describe the actual condylar path, nor do they give adequate information for articulator setup. Left-right side condylar inclination differences greater than 10 degrees can be considered as normal.

Effects of Wire EDM on the Microstructure of P/M Titanium Samples.

PURPOSE: Commercially pure titanium (CP Ti) has been recognized in dentistry for its biocompatibility, good mechanical properties and corrosion resistance. Conventional manufacturing processes can affect surface quality and result in poor bonding of dental ceramics to CP Ti. This is why powder metallurgy (P/M) and wire electro-discharge machining (WEDM) are being introduced in the manufacturing process. The aim of this study was to evaluate the effect of WEDM on the surface composition and microstructure of P/M CP Ti samples produced for bond strength testing according to ISO 9693. MATERIALS AND METHODS: Eight samples of P/M CP Ti, dimensions according to ISO 9693, were made using WEDM and divided in two groups (untreated and grinded). Microanalyses of chemical composition and microstructure of both groups were made using SEM, EDS and XDR. RESULTS: SEM and EDS analysis of untreated samples showed a thin layer on surfaces with fractures in it. Grinded samples showed homogenous structure with no layer and no fractures. XDR analysis showed high level of oxides on the surface of untreated samples, while after grinding only pure α-phase was found. CONCLUSION: WEDM is a suitable method of sample production for ISO 9693 if accompanied by grinding with silicon carbide papers P320-P4000.

Psychological status and recurrent aphthous ulceration.

Recurrent aphthous ulceration (RAU) are a disease of an unknown etiology and mediated through T-cell lymphocytes. Evidence suggests that RAU is connected with chronic bowel disease, haematinic deficiencies, AIDS, food hypersensitivity and severe stress. The aim of this study was to determine whether differences in anxiety and depression could be seen in patients with RAU during acute phase and remision period and in comparison to the healthy controls. There were 30 patients with RAU (age range 36.27 +/- 15.308) and 30 controls aged 29.83 +/- 9.082. Every participant with RAU fullfilled STAI and Beck Depression Inventory II test during acute phase and during remission period as well as controls. Statistical analysis was performed by use of descriptive statistics and t-test. There are no differences in the level of depression and stress between the two phases of the RAU (acute versus remission period) as well as in comparison to the controls. Patients with acute RAU are more anxious than patients with RAU during remission period. We might conclude that psychological disturbances do not preceed the development of RAU and that the patients with acute RAU are more anxious when compared to the condition when they do not have RAU due to the discomfort they experience.

Epidemiological study on prosthodontic appliance deliveries within elderly cohorts in the Republic of Croatia, 2002-2006.

Number of the dentate subjects among the elderly is dramatically increasing, as is the elderly proportion in overall population. Such trends indicate more need for prosthodontic appliances in elderly. The aim of this investigation was to determine the distribution of various prosthodontic appliances in older age cohorts, subventioned by the Croatian Institute for Health Insurance. Data on various prosthodontic appliances subventioned by the CIHI and delivered in all Croatian districts in the period 2002-2006 was obtained and statistically analyzed relative to 4 age cohorts of 50 and more years. The oldest age cohort (80+) showed the least appliance deliveries. The most frequently delivered appliance in all age groups were partial removable dentures (382 456 deliveries). Significantly less deliveries in the oldest age cohort compared to other groups (p < 0.05) suggest that the oldest elderly patients tend to maintain prosthodontic appliances for a longer period than functionally acceptable.

3-D stress analysis in first maxillary premolar.

The aim of this study was to investigate the stress distribution in a 3-D model of two-rooted tooth (first maxillary premolar) under two different occlusal force vectors by using finite element analysis. In the first model overall force of 200 N was divided into three vectors (cusp to fossa occlusion), and in the second model overall force was divided into 4 vectors (cusp to fossa and cusp to marginal ridge occlusion). The greatest compressive stress was found at the dentino- enamel junction in the cervical area of the both models (about -200 MPa). The greatest tensile stress was found at the vestibular aspect of buccal cusp in second model (about +3 MPa) and in the central fossa of the both models (about +28 MPa). Results indicate that in the both types of occlusal loadings the stress distribution was mainly compression and compressive forces were predominant over tensile stresses. In the second model with 4 vectors, stresses generated in the tooth structure were higher compared to the stresses generated in the first model with 3 vectors.